WTS: MG42 & MG34 2-Pcs. Blank-Bdl-Assm./WTB: Used Barrels.

[Blanksguy]

NOTE: This is a two-part-ad....."WTS" and "WTB".

WTS: 2-pcs. Blank-Barrel-Assemblies for the MG42 and MG34.

1: The MG42/SA42/MG1-3/M53 2-pcs. Blank-Barrel-Assemblies will come as pictured below with an 8x57mm rear-section and an additional rear-section in 7.62x51mm/.308 ....these are set up as "sets".
The muzzle for these is already drilled and taped for common 1/2"x20TPI Allen-Set-Screws (again, as the below photos show).

Price as pictured is $525 plus shipping to your street-address.
NOTE: The center-set in the photo has some light pitting on the outside of the front-section and is priced at $495 plus shipping to your street-address. This one set is set-up for 1/2"x13TPI Allen-Set-Screws. This set was used in my C&R FA MG42.

2: The MG34/SA34 2-pcs. Blank-Barrel-Assemblies will come as pictured below.....as 8x57mm Blank-Barrels are already available, these will only come with the 7.62x51mm/.308 rear-section. Muzzles are pre-drilled and taped for common 1/2"x20TPI Allen-Set-Screws (again, as the photos below show).
Price as pictured is $325 plus shipping to your street-address.

3: I have one (1) MG34/SA34 2-pcs. Blank-Barrel-Assembly-Set that has both the 8x57mm and an additional 7.62x51mm/.308 rear-section fitted to it. This was used in my C&R FA MG34.
Priced at $525 plus shipping to your street-address.

NOTES:
1: I have not had a chance to drill & photo the allen-set-screws.......each set purchased will come with four (4) 1/2"x20TPI Allen-Set-Screws that are only "pilot-drilled".
2: Payment can be either Money-Order or Check....all non-PMOs will be held the (10) working-days to clear Bank.
3: These are not collector-grade barrels....there are some nicks and wrench-marks and may need the blueing touched-up and/or refinished........they were selected for use to make "Blank-Barrel-Assemblies".
4: Last....if you are interested in any of these/want to purchase....or have barrels to sell/trade, contact me at my e-mail address listed below. As these Blank-Barrel-Assemblies will be listed on other web-pages, I will be tracking these by date/time receipt of e-mails at my e-mail address.

WTB.....WTB......WTB......WTB......WTB......WTB......WTB......WTB....
I am in need of both MG42/MG1-3/M53 Barrel-Assemblies and MG-34 Barrel-Assemblies, with or without the extensions.....or I will not be able to make another short run of these 2-pcs. Blank-Barrel-Assemblies. They can have shot-out dark-bores as long as the chambers and extensions are good.
***NOTE: I can take used MG42/MG1-3/M53 Barrel-Assemblies and MG34 Barrel-Assemblies in as partial-trade on the above Blank-Barrel-Assemblies........or purchase them out-right. E-Mail me at my below listed e-mail address and we can talk about this.

Regards, RichardS in MI.
Blanksguy2001@chartermi.net

[MG34Biker]

I have a spare MG34 Barrel Extension, I was hoping to have a Nato extension turned for my existing 2pc blank bbl.

[fourfifths1911]

parts recevied awesome work richard thanks any ideas on hole size for pof blanks

[Blanksguy]

fourfifths1911,
Thank you.

To help others when I answer your question....please address it on either the MG34-Section or the MG42-Section....under the "Blank-Adapting-Thread". This will allow others to gain some more information/starting-points..........and would also be the proper place to place the "question" as this "ad" won't be around after they are all sold.

Note: Only one set of MG42 Blank-Barrel-Assemblies "fitted-set" with both 8x57mm and 7.62x51mm/.308 extention/pistons available now.......I may have another MG34 2-pcs. Blank-Barrel-Assembly.

Regards, RichardS in MI.
Blanksguy2001@chartermi.net

[H0ffmn]

Richard,
Do you still have any of the MG 34/SA 34 two piece blank barrel assemblies for sale,I want to purchase one if so.
Thanks,
Mark Hoffman

[Blanksguy]

I still have one fitted-set of Blank-Barrel-Assemblies for the MG42 left.
Comes in both 8x57mm and 7.62x51mm/.308

As all of the MG34 .308 2-pcs. Blank-Barrel-Assemblies are now gone/sold......I am gauging interest in another short run of these.
If I get enough interest, I will accept payments for them and then have the machinist start work........if not, we will put this on the "back-burner" for a later date. E-mail me directly at my below e-mail address if you want one of these.

Regards, RichardS in MI.
Blanksguy2001@chartermi.net

[bbravn]

Blanksguy:

Regarding the two piece blanks adaptation assembly I wanted to buy from you my email address is bbraun2@gmail.com.

Thanks

B Braun
847-927-0777

[Blanksguy]

******With lower prices shipped to lower 48-states********

I will be going back over to pick up the next group of MG42 and MG34 2-pcs. Blank-Barrel-Assemblies shortly...and have two of the "L" shaped Feed-Tray-Spacers left over now. I believe that I will have the following for sale and taking orders now:

1: For the MG42:
A: 2-pcs. Blank-Barrel-Assemblies in either 8x57mm or 7.62x51mm/.308 cal. at $315 shipped lower 48.
B: 2-pcs. Blank-Barrel-Assemblies in both 8x57mm and 7.62x51mm/.308 cal. at $515 shipped lower 48.

2: For the MG34:
A: 2-pcs. Blank-Barrel-Assemblies in either 8x57mm or 7.62x51mm/.308 cal. at $315 shipped to lower 48.
B: 2-pcs. Blank-Barrel-Assemblies in both 8x57mm and 7.62x51mm/.308 cal. at $515 shipped lower 48.
C: One "L" shaped Feed-Tray-Spacer (final-fitting required) at $45 shipped to lower 48.........."or" I can add one to any 2-pcs. Blank-Barrel-Assembly order for an additional $35. (Shown in photo below).

I am still in need of MG42 Barrel-Assemblies.....e-mail with what you have for sale/trade on the above.

Regards, RichardS in MI.
Blanksguy2001@chartermi.net

[bmwr12]

I have a MG34 barrel that came with my semi that has a bad chamber and would probably be perfect for use to make a 2pcs blank barrel if you are interested. Thanks

[cjdaigle2]

I'd like the spacer please

[Blanksguy]

You'll have to contact me at my E-Mail address listed below for ordering information:

Blanksguy2001@chartermi.net

Regards, RichardS in MI.
Blanksguy2001@chartermi.net
US Army, Retired.

[Blanksguy]

Update: January 2010...........
I figured that I have not posted anything here for a while......this is an "up-dated" list of the items that I have just got in and ready to ship:

1: 2-pcs. Blank-Barrel-Assemblies for the MG34/SA34 in either 7.62x51mm/.308 or 8x57....or both calibers: I now have three (3) sets of these 2-pcs. Blank-Barrel-Assemblies in house at this time. $315 shipped for either caliber or $515 shipped for both calibers.

2: "L"-shaped "steel" Feed-Tray spacers: I now have three (3) of these in house ready to ship: $45 shipped each.

3: "L"-Shaped "steel" Feed-Tray spacers mounted on a WWII German Feed-Tray (ready to use): $160 shipped.

4: Spare MG34 Feed-Tray for mounting your "L"-shaped Feed-Tray spacer: $100 shipped. (Note: this tray has a tiny 1/8" crack that should be welded prior to use.).

5: 2-pcs. Blank-Barrel-Assembly for the MG42/SA42/M53 series in either 7.62x51mm/.308 cal. or 8x57mm ...or both calibers: I have three (3) sets of these 2-pcs. Blank-Barrel-Assemblies in house ready to ship......$315 shipped for either caliber.....or $515 shipped for both calibers.

NOTE: Shipping with orders is for "Lower-48" only.

E-mail me direct if you have questions or would like ordering information:
Blanksguy2001@chartermi.net

Regards, RichardS in MI.
Blanksguy2001@chartermi.net