MG34 Receiver Basic Dimensions
MG34 Receiver Basic Dimensions
Here is a drawing showing the major dimensions needed for re-welds.
All NFA rules apply.
You can see the full size drawing here: http://www.autochart.com/MG34/MG34RecBasicDim.jpg
All NFA rules apply.
You can see the full size drawing here: http://www.autochart.com/MG34/MG34RecBasicDim.jpg
"It is well that war is so terrible -- lest we should grow too fond of it." Gen. R.E. Lee CSA
Skype ID: ACE1100
Skype ID: ACE1100
Re: MG34 Receiver Basic Dimensions
Yes,thanks,Orin.I tried to do this once and made a mess of it. It will be handy when I try to figure out if I have enough material for a receiver. ---bil
"I dream of a world where I can buy alcohol,tobacco and firearms from the same drive-up window,and use them all on the way home from work!" Dogbert
Re: MG34 Receiver Basic Dimensions
Glad to help guys. Let me know if you need any other dimension.
Orin
Orin
"It is well that war is so terrible -- lest we should grow too fond of it." Gen. R.E. Lee CSA
Skype ID: ACE1100
Skype ID: ACE1100
-
- Administrator
- Posts: 3292
- Joined: Fri Jan 11, 2008 6:03 pm
- Anti-spam: Mg42
- Location: Florida
Re: MG34 Receiver Basic Dimensions
As said before MANY THANKS for posting this...
Sorry that I missed out on your mg42 receiver cut sale....
Thanks Later 42rocker
Sorry that I missed out on your mg42 receiver cut sale....
Thanks Later 42rocker
Re: MG34 Receiver Basic Dimensions
Thanks 762x51 for posting the good info
Does anyone know if any 34 rec ordnance drawings exist for all the dims of the 34 rec to scratch build one???
C
Does anyone know if any 34 rec ordnance drawings exist for all the dims of the 34 rec to scratch build one???
C
-
- Administrator
- Posts: 3292
- Joined: Fri Jan 11, 2008 6:03 pm
- Anti-spam: Mg42
- Location: Florida
Re: MG34 Receiver Basic Dimensions
There has been several good posts on this website about making one. However that said take a good look at the following website
http://www.tnwfirearms.com/photos.shtml
Note the equipment that they use to make the receivers. There has been talk about edm equipment and other things being used. I wish you a lot of luck.
Lots of folks buy several mg34 cut receivers and re-weld them...
Later 42rocker
http://www.tnwfirearms.com/photos.shtml
Note the equipment that they use to make the receivers. There has been talk about edm equipment and other things being used. I wish you a lot of luck.
Lots of folks buy several mg34 cut receivers and re-weld them...
Later 42rocker
Re: MG34 Receiver Basic Dimensions
for prints,try Maschinengewehr34.com Glenn Fahrquhar He sold some sets here,
i have one somewhere,but as mentioned above,the expensive machinery used would keep most from going the avenue. ---bil
i have one somewhere,but as mentioned above,the expensive machinery used would keep most from going the avenue. ---bil
"I dream of a world where I can buy alcohol,tobacco and firearms from the same drive-up window,and use them all on the way home from work!" Dogbert
-
- Administrator
- Posts: 3292
- Joined: Fri Jan 11, 2008 6:03 pm
- Anti-spam: Mg42
- Location: Florida
Re: MG34 Receiver Basic Dimensions
The set of prints that Fahrquhar put out are nice ones. Think long and hard before you think of starting to make a mg34 receiver from scratch. That said it's been done by several countries and at least one company.
Later 42rocker
Later 42rocker
-
- Friendly New Guy
- Posts: 4
- Joined: Tue May 20, 2008 2:33 am
Re: MG34 Receiver Basic Dimensions
Does anyone have the front end blue prints for the cam location and rivet holes? Thanks.
Re: MG34 Receiver Basic Dimensions
Interesting. As far as i can read blueprints this info is NOT in the J&G/ Farquist prints.
Would it not be in the TNW semi package?
Would it not be in the TNW semi package?
FNG