Where to find 34 receiver????

ARH · Post by **ARH** » Mon Jan 30, 2006 11:32 pm

I need a 34 receiver for a post sample build.
Can anybody point me in the right direction?
Any help would be appreciated.
Thanks

ARH

Post by **MauserMatt** » Tue Jan 31, 2006 12:04 am

IMA has em...

http://www.ima-usa.com

Supposedly they're cut really nice and should be a good reweld... That's whay I hear anyway.. Haven't bought one yet.

Post by **MauserMatt** » Tue Jan 31, 2006 12:24 am

I take that back.. I just ordered one...

:-P

I'll take pics when it gets here.

Post by **Bullwinkle** » Tue Jan 31, 2006 9:31 am

For a Post Sample Philly Ordnance or TNW would be good starting point for a "complete" uncut receiver.

Post by **Blanksguy** » Tue Jan 31, 2006 10:25 am

TNW's web-page lists down for you to contact them directly is you are a C2/07 wanting to do a Post-Sample.....I believe that they do short runs of C2/07 full-auto MG34 receivers at 80% for this purpose.......contact them.......AND please let us know some basic information as to differences in 80% receivers...and "Pricing".

Also, while you are on the phone with them...ask if they cam provide some/any of the small replacement parts and springs.......maybe they have a parts-list that they can e-mail/FAX you with prices?

Be safe, RichardS.
Blanksguy2001@chartermi.net

ARH · Post by **ARH** » Tue Jan 31, 2006 2:35 pm

MauserMatt wrote:I take that back.. I just ordered one... :-P

I'll take pics when it gets here.

Thanks for the reply MauserMatt.
You might want to check back with IMA.
This is what their site says about the receivers.

MG 34 DEMILLED RECEIVER
[GG3486]
$100.00
MG 34 DEMILLED RECEIVER
View in New Window

ORIGINAL ITEM: We have received a new shipment of torch cut receivers which comply with BATF specifications. These CANNOT be made to work again, but could be used for display guns.

The woman I spoke with on the phone said she did not have receivers suitable for rewelds.

ARH

Post by **Blanksguy** » Tue Jan 31, 2006 3:38 pm

ARH,
....and what did "TNW" tell you about their C2/07 80% receivers and parts? (IE: Pricing and availability?).

Thanks, RichardS.
Blanksguy2001@chartermi.net

ARH · Post by **ARH** » Tue Jan 31, 2006 4:40 pm

Blanksguy wrote:ARH,
....and what did "TNW" tell you about their C2/07 80% receivers and parts? (IE: Pricing and availability?).

Thanks, RichardS.
Blanksguy2001@chartermi.net

RichardS

I am still waiting for a call back from them.
The woman I spoke to said the guys with the info I needed were not there at the time.
It is now 4:40 pm my time, so I don't think I will hear back from them today.
I will post the info I get from them.

ARH

EZFEED · Post by **EZFEED** » Tue Jan 31, 2006 8:49 pm

Hey guys, well I may not be some folks favorite person at the moment but I would like to help and give y'all some pics of the recievers. NO THIS IS NOT AN ADVERTISEMENT AS WE ARE NOT SELLING THESE.

http://www.weaponeer.net/forum/forum_po ... PN=1&TPN=2

This thread has some pics of one of 4 that I recently purchased from IMA and let me just say that they are fantastic. I find them an easy breezy reweld after annealing and then preheating.

Hope this helps a little and at least you can see what they look like now. I really like them.

Post by **MauserMatt** » Wed Feb 01, 2006 2:11 am

ARH wrote:
MauserMatt wrote:I take that back.. I just ordered one... :-P

I'll take pics when it gets here.
Thanks for the reply MauserMatt.
You might want to check back with IMA.

*snip*

The woman I spoke with on the phone said she did not have receivers suitable for rewelds.

ARH

Well.. I'm hoping they only say that to cover their own butts... Cause going by what EZFEED has gotten from them, they should be weldable... in fact, you're the main reason I bought from IMA EZFEED!! :p Hope you're right.. But if not.. oh well! Still be neat to have...

EZFEED · Post by **EZFEED** » Wed Feb 01, 2006 2:20 am

They should be really really nice and I'm positive that you'll like them!

Out of all 4 the biggest variance between them were a little over 3/16" of an inch which is just remarkable to me

Christian said that they were all "carefully cut" the same and I guess he's right! Make sure just as an extra means of precaustion that you email them and state that this will be for a reweld because I think he gets allot of calls for those. I say that because he seemed to know exactly what I was talking about when I emailed him about it

Post by **TOM R** » Wed Feb 01, 2006 9:36 am

I did not look at the pics but I got 2 of these recievers from them a few months back and they look clean and doable (in my ignorant opinion) But at the time they stated that they only had 100 cut this way and were keepin it on the hush side, i payed for the handselect also ( I suggest doin this) as they also have the standard crap ones, I need be i could make 1 from 2 as the cuts overlap between the 2 I got

Farmer Mike · Post by **Farmer Mike** » Wed Feb 01, 2006 5:33 pm

I ordered two receivers from IMA. Both were cut in almost identical spots leaving no overlap. They are probably weldable but some of the smaller holes have been destroyed. Has anyone got a receiver from IMA with cuts through the trigger group pin holes? Mine had no cuts through the threads or front pin.

CHODE · Post by **CHODE** » Sun Feb 05, 2006 9:54 am

I have some receiver pieces I was going to post on gb but Ill offer them here first. 3 rear sections threads uncut. no front section with cams/halfscrew. {sorry used them on the tnw} pics on request. leave me a notice here as im having email issues. 40.00 plus shipping

BELTLEAD · Post by **BELTLEAD** » Mon Feb 06, 2006 4:03 am

I'll buy those MG34 pieces from you.

CHODE · Post by **CHODE** » Mon Feb 06, 2006 1:02 pm

sold. pending payment

Farmer Mike · Post by **Farmer Mike** » Thu Feb 09, 2006 9:00 pm

I just got a third receiver from IMA and this one is the best of the three. All the smaller holes on the exterior of the receiver are intact and the cuts are not as wide. The other two are weldable but would require more machining.

Post by **Hole_Puncher** » Fri Feb 10, 2006 6:33 pm

My IMA receiver arrived yesterday. Overal in good shape. It's a little bent from side to side but it can be fixed pretty easy. The cam area and threaded area are in good shape.

Post by **MauserMatt** » Sat Feb 11, 2006 9:36 pm

Got mine yesterday too... Same story as yours Hole Puncher..

I'll post some pics tomorrow.. Although.... Even though the cuts don't look too bad, it looks like it's going to take some work to weld these correctly.. Like I said, the cuts are good and pretty clean, but these are milled receivers so it looks like it's going to be tough to me (though I'm definitely no professional)....

Pics tomorrow!