Welding & build services

[Pirate]

We will start offering welding and build services for the semi auto MG42 in about a week or so.

The most basic service we will offer is to weld up Wise Lite Receivers to your M53 or mg42 barrel shroud and install the booster bushing, up to a completely finished gun based on the wise lite design. Prices will start at $250.00 and go up from there depending on how much work you want done.

We will be submitting samples of re welded receiver mg34 & mg42 With my bolt & FAL grip conversion to the BATF in the next week or so to be able to build these guns with an approval letter.

If you have questions contact me or Jorge at the shop 561 394- 8228 or by email:
conatact@projectguns.com
jorge@projectguns.com

We are also currently offering build services for the 1919a4, Bren, and will be offering semi RPD builds soon.

We do not offer any 80% services, so please don't even ask.

[Bil]

Good to see you guys moving along on your venture-looking forward to the new projects.You may want to cross-post your ad in the 'suppliers' section also. ---bil

[Michael J]

Bout a 79% receiver? sorry, just kidding. Definitely have to send you guys my grip stick and bolt one of these days when i round up some cash... *sigh*. Depending on how frustrated i get when i get around to actually doing some real building, i may just have to send you some cash and my other parts too .
Very nice price though!

[TbcSEOD]

[Pirate]

We have gotten several requests to finish or repair homebuilt guns or receivers that have been worked on. We do not accept any guns not built by a licensed manufacturer and marked with their information and ser # as required by the BATF.

We Also will not build any semi auto mg42's with an ar15 fcg or semi auto bolt conversion other than our own. we have a semi reweld 42 ready to submit using the fal fcg and V2.0 bolt set up, if and when we get an approval on this gun we will do builds based on this design.

We also have a re welded semi auto mg34 ready to submit and will do builds on your cut parts when and if we get an approval.

[Bil]

Pirate-will you do rewelds on receivers only,meaning a customer can do the rest of the work themselves? I realize this also means first installing a FA bolt block and making the cut to prevent original grips from being installed.So if I was to send you 34 receiver pieces,you would be able to reweld it? I am assuming if you did,it would have a number and name on it? Thanks.Glad to see you have some versions up for review.Good luck,guys! ---bil

[FMF]

I see You are doing a Bren Build , Will You be able to do a ZB 30 build after Your Bren is approved , Thanks

[Pirate]

We will do builds or receiver re welds with parts that have not been worked on. we got a large amount of receiver scrap for the 34 to use as fillers so we can do a quality restoration. we can just build the receiver for you if that is all you want.
we will quote prices on an individual basis for these as the labor involved will vary from gun to gun

on the mg42 semi, we can weld your receiver to your shroud and install the barrel bushing if that is all you want done. we can get wise lite receivers to build you a finished receiver from your shroud also.

we will be doing the zb builds based on the wise lite approval letter and with their semi parts. we have gotten their permission to do this as they are to busy to do just one or two guns at a time.

for every ones information building a semi from an m53 kit or doing a reweld from a cut receiver is a lot of work. to get a gun to function properly & reliably is a time consuming process. the kits purchased from Angola are a complete set of parts, but are not a matching set of parts from a working gun, and the m53 builds require a lot of final fitting to get them to run, that is why a build from a kit will run as much as a complete gun.

[URAR1004]

Any news from the BATFE on your summited Semi-MG42 Samples?