Cocking handle help!

Post by **Intruder196** » Mon Apr 04, 2005 11:07 pm

The spring inside my cocking handle is broken as the handle simply flaps around. My spring is definately shorter than the ones pictured for sale on gunbroker, and all those are shown disassembled. Can any of you post a pic of how the spring should go once I get a replacement?

Post by **TOM R** » Tue Apr 05, 2005 9:21 am

I can try to do it when i go home tommorow unless someone beats me to it

Post by **TOM R** » Tue Apr 05, 2005 11:34 am

here are the pics though it is hard to see, the spring goes in the smaller pin and the small L part goes to the rear the long piece goes forward, and above the large "stop" here are also some real bad drawlings soory i have reached my max upload quota will try to email them

Jason · Post by **Jason** » Tue Apr 05, 2005 12:40 pm

tom. could you send the pics to me as well. the damn spring is kicking my butt trying to figure it out. thanks

Post by **TOM R** » Tue Apr 05, 2005 1:08 pm

I will do it tomorow as i am not at home now unless intruder can forward them to you

Post by **salt6** » Tue Apr 05, 2005 6:11 pm

Tom,

Try posting again.

Steve

Post by **Intruder196** » Tue Apr 05, 2005 6:13 pm

Thanks for the pics Tom, I was able to unravel one coil on the broke spring and reinstall it. It works but is kind of weak so i will need to find a suitable replacement.

Jason · Post by **Jason** » Wed Apr 06, 2005 10:04 pm

yes thanks I got the pics as well. I'll give the spring thing a shot later.

the drawing was a true work of art

Post by **TOM R** » Thu Apr 07, 2005 9:17 am

gee thanks i had just stopped in so i was in a hurry not alwways at that house during the week

Jason · Post by **Jason** » Thu Apr 07, 2005 10:04 am

Post by **Pirate** » Tue Aug 30, 2005 7:37 pm

Does some one have a photo / drawing of how the spring goes in?

Karbinator · Post by **Karbinator** » Tue Aug 30, 2005 11:05 pm

If i didn't have the example of one assembled, I would have never figured that one out.
Did you get a Brp set to compare?

The spring was the last thing I put in. I installed the rear and front parts in there, and inserted
front pin completely. I then layed the spring in there (long end to rear, short to front) Layed a flat
file in over the top, and levered it downward till I could work my roll pin in there (use new stuff)

I'll work on a pic....but it's all out in the shop....sorry

Karbinator · Post by **Karbinator** » Wed Aug 31, 2005 2:20 pm

Pirate.... spring goes in with short to the rear, and long to the front...I just checked...

Post by **Pirate** » Fri Sep 02, 2005 7:45 pm

This thing has me totally baffled, The spring I got with my kit was a rusty POS It broke
trying to install it. Now I need a giant rubber band for test firing!

Post by **TOM R** » Fri Sep 02, 2005 9:21 pm

you don't need the cocking handle spring to test fire the thing only moves when you manualy cock for the first round, not like the m2 or 1919

Post by **JBaum** » Sat Dec 12, 2015 3:59 pm

The German wartime wrenches sell for over $200, this one is $45 delivered. This is Norwegian production, as evidenced by the part numbers stamped, and is the same as the German wrench except for having a part number and lacking a little eagle. I have 2 for sale. This wrench is 4-1/2" long and is usually kept in the tool pouch worn on the gunner's belt. Click on the picture to see a close-up.

Post by **JBaum** » Sat Dec 19, 2015 7:19 pm

One sold pending funds

One still for sale

Post by **JBaum** » Mon Mar 21, 2016 1:29 pm

Lafette wrenches are all sold.

Thanks,

John

Post by **dogman5** » Sun Oct 17, 2021 11:09 am

Good morning all,

I have for sale a dummy MG34 receiver with charging handle, buffer and buttstock. The receiver was welded together from original components and the rear end was dot manufactured. The charging handle and buffer were once welded to the receiver, but are now ground loose so they can be removed. Receiver comes with top cover pin and dust cover assembly installed.

The charging handle was unfortunately ground to fit the receiver. It does still hold as a dummy piece in a normal receiver, but has been ground down too much to allow it to pull a bolt back in my semi receiver. Works great in this receiver though.

Pictures are located here. https://www.dropbox.com/sh/i0rzojvmuw13 ... AwyPa?dl=0

Please see pictures below and ask any and all questions. I’m asking 700 plus shipping for the lot. I’m also willing to take MG34 parts in trade depending on what is offered. Thanks,

Brian

Post by **dogman5** » Mon Jan 17, 2022 7:07 pm

www.MG42.us

Cocking handle help!

Cocking handle help!

.

.

.

Lafette Wrench

Re: Lafette Wrench

Re: Lafette Wrench

MG34 Receiver, Charging Handle and Buttstock

Re: MG34 Receiver, Charging Handle and Buttstock