New members must contact admin@mg42.us to have their account activated. Please include your username.

salt

Buffer cam pieces, clean up or buy new?

Anything MG42 related.
ScottishTerrier
Hauptgefreiter
Hauptgefreiter
Posts: 5
Joined: Sat Nov 14, 2015 11:01 am
Anti-spam: Mg42

Buffer cam pieces, clean up or buy new?

Postby ScottishTerrier » Sun Nov 15, 2015 12:05 pm

Hi builders. In my kit, my upper and lower buffer cam piece are a mess, rivets in them and such. Did you clean yours up for your build or buy new? I noticed apex has new clean ones for sale on their site.

If you cleaned yours up, how did you go about it?

User avatar
www.Prussia.us
General
General
Posts: 1051
Joined: Sun Jan 06, 2008 7:17 pm

Re: Buffer cam pieces, clean up or buy new?

Postby www.Prussia.us » Tue Dec 08, 2015 9:20 pm

First congrats on your journey to rebuilding the iconic Mg42/M53.

Second w/o pictures to see how badly yours are damaged it is hard to tell what you are up against;

Though the vast majority of de-milled M53kits now just give you the buffer tabs attached to a small piece of receiver, then you merely drill the rivets out-(as I am sure you know) and assess the damage, sounds like you may have a kit like the ones Mg43.com use to sell, or some of the older Mg42 4-cut receivers, where sometimes the last cut went right through the buffer tab, then the answer is, IT DEPENDS.

Usually when doing a build most people are trying to save some money, I get that, but you do not want to try to salvage a piece that will cause endless headaches when you are in the final stretch. That said, a true craftsman can fix anything, maybe you are in that category, if like most of us and you are a weekend warrior, then the question is, can you can make that piece come back to spec. In theory if you have a good jig, and you re-weld it true, and there is not weld oozing out of the channel for the buffer tabs on the buffer to rotate, it should work. I would posit so long as the corners on the tab are still true, and again the receiver is welded to spec, I have seen plenty of tabs cut in half salvaged, even the recoil plate can be salvaged many times on those old 4-cuts.

Good luck!
“… corporations have been enthroned, and an era of corruption in high places will follow, … until all wealth is aggregated in a few hands and the Republic is destroyed.”

- Abraham Lincoln (Republican), Nov. 21, 1864

along
Feldwebel
Feldwebel
Posts: 63
Joined: Sun Dec 06, 2015 6:41 pm
Anti-spam: Mg42

Re: Buffer cam pieces, clean up or buy new?

Postby along » Sat Oct 08, 2016 6:29 pm

Hi guys,

so I am fitting my buffer tabs now and have the same question.

Does the top buffer tab look set inside the buffer deep enough?

I don't think the bottom is.

Thanks
Attachments
107_0024.JPG
Buffer tabs in buffer

anjongni
Oberstleutnant
Oberstleutnant
Posts: 419
Joined: Sun Jan 03, 2010 9:31 am
Anti-spam: Mg42

Re: Buffer cam pieces, clean up or buy new?

Postby anjongni » Sun Oct 09, 2016 10:04 am

The overall length of the buffer tabs isn't critical, it's "the distance from the rear of the receiver to the foreward edge of the tab" that is important. Nobody want a floppy buffer/stock back there.
You weld them in "a little deep" (too far foreward), then machine off metal a little at a time from INSIDE, the front edge, until your buffer just barely twists into place with a little help. It will loosen up in no time.
Best of luck....Phil


  • Similar Topics
    Replies
    Views
    Last post

Return to “MG42 General Discussion”



Who is online

Users browsing this forum: No registered users and 4 guests