MG34 Receiver Basic Dimensions

The resting place of MG34 Knowledge.
User avatar
762x51
Oberst
Oberst
Posts: 517
Joined: Wed Mar 09, 2005 8:31 pm
Location: North Carolina
Contact:

MG34 Receiver Basic Dimensions

Postby 762x51 » Sun May 03, 2009 1:37 am

Here is a drawing showing the major dimensions needed for re-welds.
All NFA rules apply.

You can see the full size drawing here: http://www.autochart.com/MG34/MG34RecBasicDim.jpg

Image
"It is well that war is so terrible -- lest we should grow too fond of it." Gen. R.E. Lee CSA
Skype ID: ACE1100

rocco1911

Re: MG34 Receiver Basic Dimensions

Postby rocco1911 » Sun May 03, 2009 10:20 pm

Thank you for posting this ... :wnana:

Bil
Field Marshal
Field Marshal
Posts: 4862
Joined: Sun Nov 26, 2006 10:21 pm
Location: Brookline,VT

Re: MG34 Receiver Basic Dimensions

Postby Bil » Sun May 03, 2009 11:08 pm

Yes,thanks,Orin.I tried to do this once and made a mess of it. :( It will be handy when I try to figure out if I have enough material for a receiver. ---bil
"I dream of a world where I can buy alcohol,tobacco and firearms from the same drive-up window,and use them all on the way home from work!" Dogbert

User avatar
762x51
Oberst
Oberst
Posts: 517
Joined: Wed Mar 09, 2005 8:31 pm
Location: North Carolina
Contact:

Re: MG34 Receiver Basic Dimensions

Postby 762x51 » Mon May 04, 2009 8:21 am

Glad to help guys. Let me know if you need any other dimension.

Orin

Image
"It is well that war is so terrible -- lest we should grow too fond of it." Gen. R.E. Lee CSA
Skype ID: ACE1100

42rocker
Administrator
Administrator
Posts: 3117
Joined: Fri Jan 11, 2008 6:03 pm
Anti-spam: Mg42
Location: Florida

Re: MG34 Receiver Basic Dimensions

Postby 42rocker » Mon May 04, 2009 10:59 am

As said before MANY THANKS for posting this...

Sorry that I missed out on your mg42 receiver cut sale....

Thanks Later 42rocker

crash520
Hauptmann
Hauptmann
Posts: 140
Joined: Wed Oct 05, 2011 11:08 pm
Anti-spam: Mg42

Re: MG34 Receiver Basic Dimensions

Postby crash520 » Tue Dec 27, 2011 4:22 pm

Thanks 762x51 for posting the good info

Does anyone know if any 34 rec ordnance drawings exist for all the dims of the 34 rec to scratch build one???

C

42rocker
Administrator
Administrator
Posts: 3117
Joined: Fri Jan 11, 2008 6:03 pm
Anti-spam: Mg42
Location: Florida

Re: MG34 Receiver Basic Dimensions

Postby 42rocker » Tue Dec 27, 2011 5:29 pm

There has been several good posts on this website about making one. However that said take a good look at the following website

http://www.tnwfirearms.com/photos.shtml

Note the equipment that they use to make the receivers. There has been talk about edm equipment and other things being used. I wish you a lot of luck.

Lots of folks buy several mg34 cut receivers and re-weld them...

Later 42rocker

Bil
Field Marshal
Field Marshal
Posts: 4862
Joined: Sun Nov 26, 2006 10:21 pm
Location: Brookline,VT

Re: MG34 Receiver Basic Dimensions

Postby Bil » Fri Dec 30, 2011 3:48 pm

for prints,try Maschinengewehr34.com Glenn Fahrquhar He sold some sets here,









i have one somewhere,but as mentioned above,the expensive machinery used would keep most from going the avenue. ---bil
"I dream of a world where I can buy alcohol,tobacco and firearms from the same drive-up window,and use them all on the way home from work!" Dogbert

42rocker
Administrator
Administrator
Posts: 3117
Joined: Fri Jan 11, 2008 6:03 pm
Anti-spam: Mg42
Location: Florida

Re: MG34 Receiver Basic Dimensions

Postby 42rocker » Fri Dec 30, 2011 7:10 pm

The set of prints that Fahrquhar put out are nice ones. Think long and hard before you think of starting to make a mg34 receiver from scratch. That said it's been done by several countries and at least one company.

Later 42rocker

toolmanm203
Friendly New Guy
Friendly New Guy
Posts: 4
Joined: Tue May 20, 2008 2:33 am

Re: MG34 Receiver Basic Dimensions

Postby toolmanm203 » Thu May 10, 2018 12:17 pm

Does anyone have the front end blue prints for the cam location and rivet holes? Thanks.

Abominog
Stabshauptmann
Stabshauptmann
Posts: 259
Joined: Tue Apr 05, 2005 1:03 pm

Re: MG34 Receiver Basic Dimensions

Postby Abominog » Fri May 11, 2018 7:01 am

Interesting. As far as i can read blueprints this info is NOT in the J&G/ Farquist prints.

Would it not be in the TNW semi package?
FNG


  • Similar Topics
    Replies
    Views
    Last post

Return to “MG34 Stickies”



Who is online

Users browsing this forum: No registered users and 2 guests