Page 1 of 1

Receiver Diagram Link

Posted: Mon Mar 07, 2005 10:42 pm
by salt6
Post this Receiver Diagram but will work on doing a cleaner copy.

http://mg42.us/web/mg42/print.jpg

Updated :wnana:

Posted: Wed Mar 09, 2005 5:52 pm
by salt6
Cleaner print at

http://www.salt6.com/MG42/Reciever%20print.jpg

If anyone has this print, could you send a copy to me.

Posted: Sun Apr 29, 2007 2:22 pm
by jstrohm
thanks e for the link

Re: Receiver Diagram Link

Posted: Wed Jan 30, 2008 12:35 pm
by par0thead151
anyone have a pictorial or review of what all needs to be done with the 80% receiver, or will all these measurements in the above photos need to be machined on a 80% half receiver?

Re: Receiver Diagram Link

Posted: Mon Apr 20, 2009 1:26 pm
by alinbancroft
Hello everyone,
Tried printing the above link. Can only get the first page. Anyone help me on this. or PM in a ttatchment?
Thanks.
Al

Re: Receiver Diagram Link

Posted: Fri Dec 23, 2011 9:31 pm
by salt6
I'll get the files up this weekend. I dropped the old provider and still need to fix some things. :wnana:

salt

Re: Receiver Diagram Link

Posted: Sun Apr 08, 2012 12:34 am
by seprice40
salt6 wrote:I'll get the files up this weekend. I dropped the old provider and still need to fix some things. :wnana:

salt

Any luck on getting that link up again?
Thanks

Re: Receiver Diagram Link

Posted: Sun Apr 08, 2012 11:05 am
by 42rocker
I'm sure that it will be worked on and WELCOME to the site.

Later 42rocker

Re: Receiver Diagram Link

Posted: Sun Apr 08, 2012 1:15 pm
by seprice40
42rocker wrote:I'm sure that it will be worked on and WELCOME to the site.

Later 42rocker
Thanks,

I just ordered my first M53 kit from centerfire and cant wait to start the build! Would you suggest the cold steel solutions industry lower for it?

Re: Receiver Diagram Link

Posted: Mon Apr 09, 2012 1:28 am
by 42rocker
There are lots of reviews on that cold receiver and most say it takes a lot of work to get it done and most don't finish it. Try Brian at brp
http://www.brpguns.com/
double check the amount of receiver that you have left on the barrel shroud after you get it and then check against brp's rear receiver half's to make sure it will work out. There are several brp built's on this site.
Also check for ima cut receivers on gunbroker.

Good Luck and enjoy the ride if possible.

Later 42rocker

Re: Receiver Diagram Link

Posted: Wed Apr 11, 2012 12:17 am
by seprice40
42rocker wrote:There are lots of reviews on that cold receiver and most say it takes a lot of work to get it done and most don't finish it. Try Brian at brp
http://www.brpguns.com/
double check the amount of receiver that you have left on the barrel shroud after you get it and then check against brp's rear receiver half's to make sure it will work out. There are several brp built's on this site.
Also check for ima cut receivers on gunbroker.

Good Luck and enjoy the ride if possible.

Later 42rocker
Thanks for the suggestion! And hope to dive into the build soon! :cross:

Re: Receiver Diagram Link

Posted: Mon Nov 12, 2012 7:56 pm
by gunnut
be nice to get the above links working again!

Re: Receiver Diagram Link

Posted: Sun Aug 09, 2015 9:19 pm
by Grapeape
is there any way to get the links back up.

Re: Receiver Diagram Link

Posted: Mon Aug 10, 2015 9:25 pm
by salt6
I'll look into getting it back.

salt

Re: Receiver Diagram Link

Posted: Mon Mar 28, 2016 11:15 am
by easymoney
Built one and tried it last Saturday. Worked great - no dented cartridges at all. However, somehow one side got pulled into the grove along side the trigger assembly and jammed the bolt. I would still give it 5 stars as I know it works. It may require a little tuning but well worth the effort.

Re: Receiver Diagram Link

Posted: Fri May 05, 2017 7:52 pm
by easymoney
Has anyone ever thought of trying to thread a hole in the front of an old trigger group and attaching a piece of the rubber hose? I have had some less than good results with the homemade version of case dent preventer.

Re: Receiver Diagram Link

Posted: Sat Nov 18, 2017 8:26 pm
by NickD
Hey guys,

Anyone have a diagram, or perhaps know what the distance is between the the front arm of the trunnion and where the 1st rivet goes? I have the BPR plans, and another one which I believe is a full auto, but it does not show the measurements there exactly. I want to know how much I need to remove from the receiver at that area. It is too long, but I needed a slightly longer receiver to work with where mine had been cut. Thank you in advance.
20171118_134413.jpg